VK 654/9 - 1654/9atmoCRAFTDE; AT; GB
8 Installation and maintenance manual atmoCRAFTThere is danger of being injured or scalded by the boiler and by all components carrying water. Only ca
9Installation and maintenance manual atmoCRAFT GB4 Assembly4.1 Installation site4.1.1 Regulations concerning installation siteThe approval of the rel
10 Installation and maintenance manual atmoCRAFT4.2 Dimensions12364690665565320Ødbc11001145a44min. 1001006904Fig. 4.1 Dimensions for VK in mmKey:1 H
11Installation and maintenance manual atmoCRAFT GB3fehD500bc12 ØØD444665565320690min. 550g1145 Da64 Øk312100d690Fig. 4.2 Dimensions for VKM in mm
12 Installation and maintenance manual atmoCRAFT4.3 Recommended minimum distance for installation1000500100BA5002200Fig. 4.3 Minimum clearancesWhen
13Installation and maintenance manual atmoCRAFT GB4.4 Boiler block, pre-assembled Note!Here you will find the scope of supply of the pre-assembled boi
14 Installation and maintenance manual atmoCRAFT4.4.2 Scope of supply, claddingCheck the scope of supply in accordance with the adjacent illustration
15Installation and maintenance manual atmoCRAFT GB4.4.4 Aligning the boiler block1Fig. 4.7 Aligning boiler blockThe boiler block must be level. Note
16 Installation and maintenance manual atmoCRAFT231Fig. 4.11 Fitting the intermediate plate and side plates• Fix one side plate (1) to the basefram
17Installation and maintenance manual atmoCRAFT GB112Fig. 4.15 Inserting the temperature sensor into the immersion sleeve• Insert the temperature s
18 Installation and maintenance manual atmoCRAFT4.7 Connection of the electrical cableFig. 4.19 Connecting the gas valves and the STL• Connect th
19Installation and maintenance manual atmoCRAFT GB123Fig. 4.23 Fitting the cover plate• Place the cover plate (1) in position. The braces (3) of the
20 Installation and maintenance manual atmoCRAFT5 Installation5.1 General instructions for heating system Caution!Flush the heating system thoroughly
21Installation and maintenance manual atmoCRAFT GB5.4.2 Connecting the mains feedFig. 5.1 Connecting the mains supplyThe nominal voltage of the main
22 Installation and maintenance manual atmoCRAFT5.4.4 Electrical connection plan with system Pro ECharging pumpHeating circuit pumpOption external con
23Installation and maintenance manual atmoCRAFT GBCharging pumpHeating circuit pumpOption external controller/room thermostat 230V contactOption exter
24 Installation and maintenance manual atmoCRAFT5.4.5 Connection of external accessories and control unitsWhen connecting accessories, the existing b
25Installation and maintenance manual atmoCRAFT GB5.4.6 Connecting external sensors, control units (accessories)Fig. 5.5 Connecting the sensors• P
26 Installation and maintenance manual atmoCRAFT Caution!Do not add frost or corrosion preventative to the heating water!If frost or corrosion prevent
27Installation and maintenance manual atmoCRAFT GBThe permissible range for the connection flow pressure is: 17.0 to 25.0 mbar - 2nd gas family (nat
For the heating engineerVK 654/9 – 1654/9Installation and maintenance instructionsatmoCRAFTGas heating boilerGB
28 Installation and maintenance manual atmoCRAFT6.2.4 Gas setting tablesType of gasNozzle designationcorresponds to the nozzle pressure diameterø in 1
29Installation and maintenance manual atmoCRAFT GB6.2.5 Function checkTo complete the gas setting it is necessary to carry out a function check as fol
30 Installation and maintenance manual atmoCRAFT6.2.7 Changeover from liquid gas P to natural gasChanging the nozzles12Fig. 6.5 Changing the nozzle
31Installation and maintenance manual atmoCRAFT GB• Point out to the user the correct (economical) settings for temperatures, regulators and thermost
32 Installation and maintenance manual atmoCRAFT7.2 Overview of the adjustable installation parametersThe following parameters can be adjusted to mat
33Installation and maintenance manual atmoCRAFT GB8 Inspection and maintenance8.1 Notes for maintenancePermanent operational readiness, safety, reli
34 Installation and maintenance manual atmoCRAFT8.3.1 Checking the safety temperature limiter12Abb. 8.1 Release button, button fault resetKey1 STL
35Installation and maintenance manual atmoCRAFT GB8.4 Maintenance tasks8.4.1 Cleaning the burner Caution!If possible, do not use any chemical cleaning
36 Installation and maintenance manual atmoCRAFTFig. 8.5 Fitting the burnerIf it is necessary to also clean the heat exchanger, proceed as per Secti
37Installation and maintenance manual atmoCRAFT GB9 Troubleshooting9.1 Error codesFor fault finding and fault rectification, the fault signal facility
2ContentsInstallation and maintenance instructions atmoCRAFTContents1 Notes on the documentation . . . . . . . . . . . . 31.1 Storage of the docu
38 Installation and maintenance manual atmoCRAFT9.2 Resetting the interlock after switch-off by the safety temperature limiter (STL)12Fig. 9.1 Rese
39Installation and maintenance manual atmoCRAFT GBDisplay Meaning Display value/adjustable valued.00 Test operation on 1st burner stage for gas settin
40 Installation and maintenance manual atmoCRAFT10 Vaillant ServiceTo ensure efficient and reliable operation of your boiler it is recommended that re
41Installation and maintenance manual atmoCRAFT GB12 Technical dataTechnical data UnitVK 654/9VK 754/9VK 854/9VK 1054/9VK 1154/9VK 1304/9VK 1504/9VK 1
835553_02 DEATGB 092006
3Installation and maintenance manual atmoCRAFT GBNotes on the documentation 1Description of the appliance 22 Description of the appliance2.1 Identifi
4 Installation and maintenance manual atmoCRAFT2.2 CE labelCE labelling shows that the appliances comply with the basic requirements of the following
5Installation and maintenance manual atmoCRAFT GB2.6 Type overviewThe Vaillant atmoCRAFT gas boilers are supplied with the following capacities:Applia
6 Installation and maintenance manual atmoCRAFT2.7 Functional and operating elements131215143416521098 711Fig. 2.1 Overview of the functional eleme
7Installation and maintenance manual atmoCRAFT GB3 Safety instructions and regulations3.1 Safety instructionsAssemblyThe combustion air fed to the un
Comments to this Manuals